Want to add drama and lift to your glam? Our Ultimate Wing individual lashes are perfect for you!

With lengths 12mm, 14mm and 16mm you can tailor your lash map for your customised snatched look. Reuse these lashes after 7 days wear by pairing with our Cleansing Mist and Invisi remover.

Why you need to try our Individual Clusters: 
- Super easy to apply
- Blends seamlessly with your lash line
- 40 Clusters per pack
- Reusable
- Vegan & Cruelty Free

Perfect for: Customisable, Russian Volume, Glam, Individual Clusters, Lash Extension Look, Hooded Eyes, Almond Eyes, Deep Set

Reusable Clusters
Adhesive not included
Length: Medium - Long

With Regular Lash Adhesive:

• Using tweezers, gently lift your selected individual cluster from the tray. Ensure your tweezer is 1mm away from the root.

• Dip the base in a small amount of glue and allow 30-40 seconds for the glue to become tacky. 
• Line the cluster up to your desired position and then place the lash onto your lash line. Secure the cluster using your tweezers.
• Continue to apply until you have achieved your desired look.

With Invisi-Lash Adhesive:

Before applying make sure your lashes are make up and oil free, and completely clean and dry. We recommend working on one eye at a time when applying Invisi-Lash and Lash Clusters.

Patch Testing : We recommend completing a patch test before using Invisi-Lash. Simply apply a small amount of Invisi-Lash Bond to a small section of outer corner lashes and wait for 24 hours. If you experience any reactions/sensitivity, please discontinue use.

1. Brush a light coat of "Bond" from the Invisi-Lash Adhesive on your natural lashes. Focus the adhesive where the base of the cluster will connect with your natural lashes, if you are going for a more dramatic cluster you may need to take the adhesive further up the lash for a stronger hold. You do not need to brush the adhesive all the way up your lash. We recommend not applying mascara before the bond for a more natural & seamless look.

Once the bond is applied, wait for 30 seconds for the bond to go tacky.

Tatti Tip! We recommend working in sections, from either the outer corner of your eye or the inner corner of your eye, working across your lash line. Working in sections will give you time to apply the bond and clusters flawlessly.

Once you have completed one section, you can then apply the bond to the next section and repeat.

If your lashes are going too sticky after applying the bond, you may be applying too much. We recommend just 1 coat of bond.

2. Gently loosen and peel your cluster from the tray using your fingers. We recommend loosening the cluster as close to the root as possible before removing from the tray.

3. Using your lash applicator, pick up your cluster from the end section of the lash (not the base.) Place the cluster underneath your natural lashes by lifting the lash cluster against the root of your natural lashes, using an up and out motion.

Make sure no adhesive is on the tweezer as this will stick to the lash cluster. If you have glue on the tweezer, make sure to clean this off in between lash applications as it can stick to the cluster and the tweezers. We love our Adhesive Wipes for this.

Tatti Tip! We recommend using a tweezer that you feel most comfortable with for the application of lash clusters.

Once you have applied all lashes to the eye you're working on, continue to step 4.

4. Apply the 'Seal' using a dabbing motion to the upper and lower sides of your finished lashes. Do not brush or pull the wand through your lash clusters. The seal will eliminate any sticky residue and cure the adhesive bond. ONLY seal the lashes where you've applied the Bond, taking care to avoid the tips of the lash clusters.

Wait 5 minutes to let the cure work it's magic. Repeat this step if you feel the bond is still sticky/tacky.

Be careful not to apply the cure all the way through the lash cluster as it can leave a residue and cause the clusters to go hard and clump together.

5. Once your lashes are set in place, using your Curved Invisi-Lash Applicator, clamp down the lashes to ensure they are secure and locked into place. Make sure you wipe down your lash applicator so there isn't any black bond on it prior to clamping. When clamping, focus on the base of your natural lash line where the lash clusters are bonded to, as this will ensure your lashes will not lift or move, giving a long lasting finish (just like lash extensions!)

Tatti Tip! Make sure your applicator does not have glue on it for an easy application. We recommend wiping the applicator down regularly if glue build up does occur.

We recommend keeping your lashes away from water and steam for 24 hours after application, just like you would with lash extensions.

Order before 9pm to receive your order the following day (Monday - Thursday, UK only). Any orders placed after 7pm on Thursday will be delivered on Monday. Any orders placed after 7pm on Saturday will be processed on Monday for Tuesday delivery (as it is a next working day service).

Please see our delivery page for shipping times and prices for your region.